BOBCAT Loader Fault Codes DTC
BOBCAT Skid Steer Loader Fault Codes DTC list
01-16 is not connected air filter
01-17 clogged air filter
02-16 Filter hydraulic / hydrostatic system is not connected
02-17 Filter hydraulic / hydrostatic system is connected
03-09 Low battery voltage
03-10 High Voltage Battery
03-11 Extremely high voltage battery
03-14 Extremely low battery voltage
03-22 Battery voltage is below the limit
04-09 Low levels of engine oil pressure
04-14 Extremely low levels of engine oil pressure
04-15 Engine oil pressure at the level of the emergency engine shutdown
04-21 Engine oil pressure above the maximum permissible
04-22 Engine oil pressure below the limit
05-09 Low supply pressure in the hydraulic system
05-10 High charge pressure in the hydraulic system
BOBCAT Error Codes DTC
05-11 Extremely high charge pressure in the hydraulic system
05-14 Extremely low supply pressure in the hydraulic system
05-15 charge pressure in the hydraulic system at the level of the emergency engine shutdown
05-21 charge pressure in the hydraulic system above the maximum permissible
05-22 charge pressure in the hydraulic system below the limit
06-10 high engine speeds
06-11 Extremely high engine speed
06-13 No engine speed signal
06-15 Engine speed at the level of the emergency engine shutdown
06-18 Engine speed is out of range
07-10 Heat the oil in the hydraulic system
07-11 Extremely high temperature hydraulic oil
07-15 The oil temperature in the hydraulic system at the level of the emergency engine shutdown
07-21 The oil temperature in the hydraulic system above the maximum allowable
07-22 The oil temperature in the hydraulic system below the limit
08-10 High engine coolant temperature
08-11 Extremely high engine coolant temperature
08-15 Engine coolant temperature at the level of the emergency engine shutdown
08-21 Engine coolant temperature is higher than the maximum permissible
08-22 Engine coolant temperature is below the limit
09-09 Low fuel level
09-21 Fuel level above the maximum permissible
09-22 Fuel level below the limit
10-17 clogged hydraulic filter discharge
11-05 frame sensor security shorted to battery
11-06 frame sensor security shorted to ground
12-21 Signal ShIMkontrollera front ext. hydraulics for the upper limit of the range
12-22 ShIMkontroller front ext. hydraulics for the lower range
12-23 ShIMkontroller front ext. Hydraulic not in the neutral range
13-05 Retaining fuel cutoff solenoid shorted to battery
13-06 Retaining fuel cutoff solenoid shorted to ground
13.7 Open circuit solenoid fuel cutoff
14-02 retracting solenoid fuel cutoff, the erroneous inclusion
14-03 retracting solenoid fuel cutoff, erroneous shutdown
15-02 retracting solenoid lock rods, erroneous inclusion
15-03 retracting solenoid lock rods, erroneous shutdown
16-05 Retaining solenoid lock rods shorted to battery
16-06 Retaining solenoid locking rod is closed to ground
17-05 hydraulic solenoid shut-off valve is closed to battery
17-06 hydraulic solenoid shut-off valve is closed to ground
17-07 Open circuit hydraulic solenoid shut-off valve
Fault Codes DTC list of BOBCAT Tractors
18-05 The solenoid slide is closed to battery
18-06 Solenoid spool is closed to ground
18-07 Open circuit solenoid spool
19-02 solenoid positioning bucket erroneous inclusion
19-03 Solenoid bucket positioning, incorrect shutdown
20-02 Solenoid switching speeds erroneous inclusion
20-03 Solenoid switching speeds, erroneous shutdown
21-02 Glow plugs the erroneous inclusion
21-03 Glow plugs, faulty shutdown
Starter 22-02, the erroneous inclusion
Starter 22-03, erroneous shutdown
23-02 Rear base solenoid erroneous inclusion
23-03 Rear base solenoid erroneous shutdown
24-02 Rear spindle solenoid erroneous inclusion
24-03 Rear spindle solenoid erroneous shutdown
25-02 Rear auxiliary proportional solenoid erroneous inclusion
25-03 Rear auxiliary proportional solenoid, faulty shutdown
27-02 erroneous inclusion of the stem of the front solenoid
28.2 Solenoid relief valve, faulty switch
28.3 Solenoid relief valve, faulty shutdown
29.2 Solenoid large supply, faulty switch
29.3 Solenoid large supply, faulty shutdown
30-28 Failure memory controller
31-28 Fault recovery mode (also appears after the software update)
32-04 Advanced Management (ACS) does not communicate with the controller Bobcat
32-23 Calibration required ACS
32-24 Calibrate ACS
32-31 Fault actuator tilt ACS
Faulty wiring 32-32 tilt actuator ACS
32-33 tilt handle the wiring ACS
32-34 ACS tilt actuator is not in the neutral position
32-35 The handle / pedal tilt bucket ACS is not in the neutral position
32-36 Fault actuator lift ACS
Faulty wiring 32-37 actuator lift ACS
32-38 the wiring arm lifting ACS
32-39 actuator lifting ACS not in the neutral position
32-40 The handle / lift pedal bucket ACS is not in the neutral position
32-41 ACS: no connection
32-49 actuator lift ASS closed to ground
32-50 tilt actuator ASS shorted to ground
32-51 actuator lift ASS shorted to battery
32-52 tilt actuator ASS shorted to battery
32-53 Handle / foot boom is closed to ground, ASS
32-54 Handle / foot slope of the boom is closed to ground, ASS
32-55 Handle / foot boom is closed to battery, ACS
32-56 Handle / foot slope of the boom is closed to battery, ACS
32-57 Reduced performance actuator lift ACS
32-58 Reduced performance actuator tilt ACS
32-59 Wrong direction of the actuator lift ACS
32-60 Wrong direction of the actuator lift ACS
32-61 Chain lock handle ACS shorted to ground
32-62 Chain lock handle ACS closed on battery
32-63 Chain lock pedals ACS is closed to ground
32-64 Chain lock pedals ACS closed on battery
32-65 Voltage sensor out of range ACS
32-66 Battery voltage ACS below the limit
32-67 Switch ACS switched during operation
32-68 Error Information Handle boom, ACS
32-70 Chain right arm movements ACS shorted to ground
32-71 Chain right arm movements ACS closed on battery
32-74 X-axis joystick left ACS is out of range
32-75 Power Off unswitched equipment ACS
32-76 Error Information joystick CAN, ACS
32-77 Error Information remote control, ACS
33-23 The main controller (controller Bobcat) is not programmed
34-04 panel with push-button starting the controller does not communicate with Bobcat
35-02 erroneous inclusion of the fan hydraulics
35-03 Mistaken off the fan hydraulics
36-48 connect multiple controllers ACD
37-02 Two-speed auxiliary switch speeds erroneous inclusion
37-03 Two-speed auxiliary switch speeds erroneous inclusion
38-01 Error Information joystick CAN
38-02 Error Information Remote Control
38-04 There is no communication with the controller joystick
38-05 X axis the left stick is not in the neutral position
38-06 X axis right stick is not in the neutral position
38-07 Y-axis of the left joystick is not in neutral
38-08 Y-axis right stick is not in the neutral position
38-09 mode switch control circuit to the battery or to ground
38-10 Calibrate actuator
38-11 lift actuator is not in the neutral position
38-12 tilt actuator is not in the neutral position
38-13 Failure of the actuator lift
38-14 Failure of the actuator tilt
38-15 Wiring Fault speed control right wheel
38-16 Wiring fault for the speed of the left wheel
38-17 Reduced performance actuator tilt
38-18 Reduced performance actuator lift
38-19 X-axis joystick for left upper range
38-20 X-axis right joystick for the upper limit of the range
38-21 Y-axis joystick for left upper range
38-22 Y-axis right joystick for the upper limit of the range
38-23 front right sensor signal controls the upper limit of the range
38-24 front left sensor signal controls the upper limit of the range
38-25 rear right sensor signal controls the upper limit of the range
38-26 rear left sensor signal controls the upper limit of the range
38-27 Signal actuator for lifting the upper range
38-28 Signal actuator for tilting the upper range
38-29 X-axis joystick left for lower range
38-30 X-axis right joystick for the lower range
38-31 Y-axis joystick left for lower range
38-32 Y-axis right joystick for the lower range
38-33 front right sensor signal controls the lower end of the range
38-34 front left sensor signal controls the lower end of the range
38-35 rear right sensor signal controls the lower end of the range
38-36 rear left sensor signal controls the lower end of the range
38-37 Power "1" 5-volt sensor for the lower range
38-38 Power "2" 5-volt sensor for the lower range
38-39 actuator lift is closed to ground / lower boundary of the range
38-40 tilt actuator is closed to ground / signal for the lower range
38-41 Wrong direction of the tilt actuator
38-42 Wrong direction of the actuator lift
38-43 left front solenoid actuator erroneous inclusion
38-44 Solenoid left reverse drive, faulty switch
38-45 right front solenoid actuator erroneous inclusion
38-46 Solenoid right reverse drive, faulty switch
38-47 Front right solenoid control switch faulty
38-48 Front left solenoid control switch faulty
38-49 Rear right solenoid control switch faulty
38-50 Rear left solenoid control off erroneous
38-51 solenoid pressure control system, the erroneous inclusion
38-52 Back-up alarm, the erroneous inclusion
38-53 Solenoid left front drive off false
38-54 Solenoid left reverse drive, faulty shutdown
38-55 right front solenoid drive off false
38-56 Solenoid right reverse drive, faulty shutdown
38-57 Front right solenoid control extension, erroneous shutdown
38-58 Front right solenoid control retraction, erroneous shutdown
38-59 Front left solenoid control extension, erroneous shutdown
38-60 Front left solenoid control retraction, erroneous shutdown
38-61 Rear right solenoid control extension, erroneous shutdown
38-62 Rear right solenoid control retraction, erroneous shutdown
38-63 Rear left solenoid control extension, erroneous shutdown
38-64 Rear left solenoid control retraction, erroneous shutdown
38-65 solenoid pressure control system, faulty shutdown
38-66 Back-up alarm, erroneous shutdown
38-67 No communication from Bobcat controller
38-68 wheel alignment (alignment) not calibrated
38-69 Fault calibration actuators lift and tilt
38-70 Fault recovery mode range
38-71 Battery voltage out of limits
38-72 Pump drive is not calibrated
38-73 Control Mode Switch switched during operation
38-74 Uncontrolled rotation speed of the right wheel
38-75 Uncontrolled rotation speed of the left wheel
38-76 solenoid pressure control system Undercurrent
38-77 Front right solenoid control extension Undercurrent
38-78 Front right solenoid control retraction Undercurrent
38-79 Front left solenoid control extension Undercurrent
38-80 Front left solenoid control retraction Undercurrent
38-81 Rear right solenoid control extension Undercurrent
38-82 Rear right solenoid control retraction Undercurrent
38-83 Rear left solenoid control extension Undercurrent
38-84 Rear left solenoid control retraction Undercurrent
38-85 Power "1" 5-volt sensor for the upper limit of the range
38-86 ° Power "2" 5-volt sensor for the upper limit of the range
38-87 Problem front right steering device for the lower range
38-88 Malfunction of the front left of the steering gear
38-89 Fault rear right of the steering gear
Error 38-90 rear left control
38-91 No speed sensor impulses of the right wheel
38-92 No speed sensor impulses left wheel
38-93 right wheel speed sensor does not respond
38-94 left wheel speed sensor does not respond
38-95 Change of direction in the left wheel speed sensor
38-96 Change of direction in the right wheel speed sensor
38-98 controller in calibration mode drive
38-99 controller in calibration mode wheel position
39-04 Left joystick has no communication with the controller Bobcat
39-05 X-axis is not in the neutral position
39-07 Y-axis is not in the neutral position
39-12 manipulator switch left stick is not in neutral
39-13 is not connected joystick handle left off
39-16 is not connected joystick left off
39-28 Internal fault of the left joystick
39-48 Left joystick, multi-mode
40-04 Right joystick has no communication with the controller Bobcat
40-05 X axis right stick is not in the neutral position
40-07 Y-axis right stick is not in the neutral position
40-12 manipulator switch right joystick is not in neutral
40-13 is not connected right stick handle
40-16 is not connected right stick
40-28 Internal fault of the right joystick
40-48 Right stick, multi-mode
41-09 Low voltage generator
41-10 High Voltage Generator
41-11 Extremely high voltage generator
44-02 Horn, the erroneous inclusion
44-03 Horn, erroneous shutdown
45-02 The right turn signal, the erroneous inclusion
45-03 The right turn signal, erroneous shutdown
46-02 left turn signal, the erroneous inclusion
46-03 left turn signal, erroneous shutdown
47-21 Power 8voltovogo sensor for upper range
47-22 Power 8voltovogo sensor for lower range
48-02 front light switch, faulty switch
48-03 front light switch, faulty shutdown
49-02 Relay rear light erroneous inclusion
49-03 Relay rear light, faulty shutdown
60-21 signal lever back ext. hydraulics for the upper limit of the range
60-22 signal lever back ext. hydraulics for the lower range
60-23 lever rear ext. Hydraulic not in the neutral position
64-02 erroneous inclusion of a power relay
64-03 Mistaken off power relay
73-04 Fault remote control
73-13 Remote control signal is missing
74-72 Fault boot code controller Bobcat
75-01 Error Information joystick CAN
75-04 There is no communication with the controller drive
75-05 X axis the left stick is not in the neutral position
75-07 Y-axis of the left joystick is not in neutral
75-08 Y-axis right stick is not in the neutral position
75-09 mode switch ISO / H circuit to battery or to ground
75-13 jammed angle sensor right front wheel
75-14 jammed angle sensor left front wheel
75-15 jammed angle sensor right rear wheel
75-16 jammed angle sensor left rear wheel
75-17 left inclined plate is not in the neutral position
75-18 right oblique plate is not in the neutral position
75-19 X-axis joystick for left upper range
75-21 Y-axis joystick for left upper range
75-22 Y-axis right joystick for the upper limit of the range
75-23 Signal angle sensor right front wheel of the upper limit of the range
75-24 Signal angle sensor left front wheel of the upper limit of the range
75-25 Signal angle sensor right rear wheel for the upper limit of the range
75-26 Signal angle sensor left rear wheel of the upper limit of the range
75-27 Offset left oblique plate
75-28 Offset right oblique plate
75-29 X-axis joystick left for lower range
75-31 Y-axis joystick left for lower range
75-32 Y-axis right joystick for the lower range
75-33 Signal angle sensor right front wheel of the lower boundary of the range
75-34 Signal angle sensor left front wheel of the lower boundary of the range
75-35 Signal angle sensor right rear wheel of the lower boundary of the range
75-36 Signal angle sensor left rear wheel of the lower boundary of the range
75-37 Power "1" 5-volt sensor for the lower range
75-38 Sensor supply 2 for the lower range
75-39 Sensor Signal Left inclined plate for the top end of the range
75-40 Sensor Signal Left inclined plate for bottom of the range
75-41 Sensor Signal Right inclined plate for the top end of the range
75-42 Sensor Signal Right inclined plate for bottom of the range
75-43 left front solenoid actuator erroneous inclusion
75-44 Solenoid left reverse drive, faulty switch
75-45 right front solenoid actuator erroneous inclusion
75-46 Solenoid right reverse drive, faulty switch
75-47 Front right solenoid control extension shorted to battery
75-48 Front left solenoid control extension shorted to battery
75-49 Rear right solenoid control extension shorted to battery
75-50 Rear left solenoid control extension shorted to battery
75-51 solenoid pressure control system is closed to battery
75-52 Back-up alarm, the erroneous inclusion
75-53 Solenoid left front drive off false
75-54 Solenoid left reverse drive, faulty shutdown
75-55 right front solenoid drive off false
75-56 Solenoid right reverse drive, faulty shutdown
75-57 Front right solenoid control extension shorted to ground
75-58 Front right solenoid control retraction shorted to ground
75-59 Front left solenoid control extension shorted to ground
75-60 Front left solenoid control retraction shorted to ground
75-61 Rear right solenoid control extension shorted to ground
75-62 Rear right solenoid control retraction shorted to ground
75-63 Rear left solenoid control extension shorted to ground
75-64 Rear left solenoid control retraction shorted to ground
75-65 solenoid pressure control system is closed to ground
75-66 Back-up alarm, erroneous shutdown
75-67 No communication from Bobcat controller
75-68 angle sensors are not calibrated
75-69 Battery voltage is above the maximum permissible
75-70 Fault recovery mode (also appears after the software update)
75-71 Battery voltage is below the limit
75-72 Pump drive is not calibrated
75-73 mode switch ISO / H switched during operation
75-74 Uncontrolled rotation speed of the right wheel
75-75 Uncontrolled rotation speed of the left wheel
75-76 There are no posts from the controller ACS
75-77 speed sensor signal of the left wheel of the upper limit of the range
75-78 speed sensor signal of the right wheel of the top of the range
75-79 speed sensor signal of the left wheel of the lower boundary of the range
75-80 speed sensor signal of the right wheel of the bottom of the range
75-81 Front right solenoid control retraction shorted to battery
75-82 Front left solenoid control retraction shorted to battery
75-83 Rear right solenoid control retraction shorted to battery
75-84 Rear left solenoid control retraction shorted to battery
75-85 Power "1" 5-volt sensor for the upper limit of the range
75-86 Sensor supply 2 for the upper limit
75-88 controller in programming mode
75-91 Changing the polarity of the left oblique sensor plate
75-92 Changing the polarity of the sensor right oblique plate
75-93 right wheel speed sensor does not respond
75-94 left wheel speed sensor does not respond
75-95 Change of direction in the left wheel speed sensor
75-96 Change of direction in the right wheel speed sensor
75-98 controller in calibration mode
76-73 left panel, the error of the receiver
77-48 Ignition Switch, multi-mode
78-74 Door / locking the lock is opened / closed
80-02 ACD, output «A», the erroneous inclusion
80-03 ACD, output «A», erroneous shutdown
81-02 ACD, exit «B», the erroneous inclusion
81-03 ACD, exit «B», erroneous shutdown
82-02 ACD, output «C», the erroneous inclusion
82-03 ACD, output «C», erroneous shutdown
83-02 ACD, exit «D», the erroneous inclusion
83-03 ACD, exit «D», erroneous shutdown
84-02 ACD, exit «E», the erroneous inclusion
84-03 ACD, exit «E», erroneous shutdown
85-02 ACD (controller attachments), exit «F», the erroneous inclusion
85-03 ACD, exit «F», erroneous shutdown
86-02 ACD, exit «G», the erroneous inclusion
86-03 ACD, exit «G», erroneous shutdown
87-02 ACD, exit «H», the erroneous inclusion
87-03 ACD, exit «H», erroneous shutdown
90-02 Service Output «C», the erroneous inclusion
90-03 Service Output «C», erroneous off wheels
91-02 Service Output «D», the erroneous inclusion
91-03 Service Output «D», erroneous shutdown
92-02 Service Output "E", the erroneous inclusion
92-03 Service Output "E" erroneous shutdown
93-02 Service Output «F», the erroneous inclusion
93-03 Service Output «F», erroneous shutdown