CLAAS Jaguar Tractor Fault Codes DTC

CLAAS Jaguar Tractor Fault Codes DTC

Code Module Fault Operating state Troubleshooting

E-1

Device CAB oil pressure engine too poor

E-2 

Device CAB Oil Level engine too low

E-3

Unit CAB Water pump defective

Charging Control lights and goes out.

Test drive water pump and generator.

Check control charge on generator

E-4

CAB Temperature cooling water too high

E-5

CAB hydraulic temperature

Coil too high

E-6

CAB Tighten the handbrake

E-19 

Apparatus CAB

Hydraulic drive motor

Coil not complies configuration

E-20

Ellectric Hydraulic

First drive running of the EFA new module EFA  absolutely necessary potentiometer study movement of the lever

This message appears after installing a new

EFA module when the ignition.

After learning

potentiometers arm and hydraulic motion flow this message no longer appears.

1. Study potentiometer

movement of the lever

2. Study hydraulic flows through

CDS system

Hydraulic oil should have labor temperature. meaning voltage pressure sensors should be < 1.2 V.

E-33

ESR ESR module defective. Check power module.

Check strength landing and contact conclusions.

E-34

AutoContour CAC module outline faulty system

Check power module.

Check strength landing and contact conclusions.

E-36 

GGS GGS Defect Test power module.

Check strength landing and contact conclusions.

E-37

Electrical Hydraulic

First drive running of the EFA

EFA faulty module Emergency stop:

During this work It indicates a defect power module output. It should be shut down.

The movement of the machine no more provided

possible.

Turn off the machine and restart, if the fault no more It appears, in another module procedure, otherwise. If not, replace module.

E-42

First drive running of the EFA Faulty third magnet

electromagnetic valve

Emergency Stop:

The machine moves on coast to stop, further movement is not provided possible. flap impossible

to govern:

Check cable module connection to the valve for a short circuit or breakage. Check the module output.

measure resistance coil range values: 6 - 12 ohms

Check plug to compound valve.

E-43

First drive running of the EFA

Defect electromagnetic pump valve motion ago

Emergency mode:

The machine moves only forward at approx. 2

km / h at the 2nd transmission 1 km / h on the 1st gear.

When you identify short the closure of the valve

It made an emergency. Stop the movement over

impossible. flap impossible to govern:

Check cable module connection to the valve for a short circuit or breakage. Check the module output.

measure resistance coil range values: 6 - 12 ohms

Check plug to compound Valve.

E-46

Check cable set to module potentiometer on open or short circuiting.

Potentiometer

Motion 2 issues opposite signal sum with which the signal potentiometer

Motion 1 is always must have permanent value.

If the total signal is not in within 7.3 - 7.5, the potentiometer movement of the lever defective.

Example:

Signal 1 = 4.0 V

Signal 2 = 3.4 V>

Amount: 4.0 + 3.4 = 7.4 B => potentiometer order.

Signal 2 = 1.0 =>

Amount: 4.0 + 1.0 = 5.0 B => potentiometer defective

measure potentiometer.

E-50

ESR does not recognize the adapter SFM box

The module identifies the ESR speed sensors

Rotation Disco 8500, but 5 are absent from adapter box.

Female compound: Check 13 pin connector on the

driver site (corrosion). Open or short closing signal wire to the ESR module.

E-51

The level of coolant the water is too low

Refuel cooling water.

Cable set or plug cause short short to ground.

E-52

ESR No recognition rotation speed feeder

Fault can be issued in multiple without reversing

causes.

When submitting a feed the device is switched off

after the issuance of reports malfunction.

Check plug to compound speed sensor rotation.

Check 13 pin connector on the driver site (corrosion).

Open or short closing signal wire to the ESR module.